Orifice Plates

Orifice Plates - Prisma Request a quote

Series : PO

 

 

Types of Orifice Plates :

  • Square Edged Concentric
  • Eccentric
  • Segmental
  • Quadrant Edge
  • Conical Entrance

 

 

 

 

 

Square Edged Concentricorifice concentric

These are most commonly used for
flow measurement. This has special features such as simple structures, high accuracy, and ease of installation & replacement. The orifice plates are correctly finished to the dimensions, surface roughness, and flatness to the applicable standard. These plates are recommended for clean liquids, gases & steam flow, when the Reynold number 7 ranges from 10000 to 10.

 

 

 

Eccentricorifice eccentric

For liquids containing solid particles that are likely to sediment or for vapors likely to deposit water condensate, this orifice plate is used with its eccentric bore bottom flush with the bottom of the piping inside surface so that the sedimentation of such inclusions are avoided. Likewise, for gases or vapors, it may be installed with its eccentric bore top flush with the ID of the piping to avoid stay of gas or vapor in its vicinity.

 

 

 

Segmentalorifice segmental

Segmental orifice plates are most useful where there are substantial entrained water or air and also if there are suspension in the fluids. This avoids build up in front of the orifice plate. The orifice hole is placed at the bottom for gas service and top for liquids.

 

 

 

 

Quadrant Edgeorifice edge

The inlet edge of the bore of this orifice plate is rounded to a quarter circle. This orifice plate is usually used for viscous fluids & Reynolds number between 2000 to 10000.

 

 

 

 

 

 

 

 

Conical Entranceorifice conical

These conical entrance orifice plates are used for low Reynolds number in the range of 80 to 2000 and give more constant or predictable discharge coefficient. At lower Reynolds numbers, the discharge coefficient of square edge orifice plate may change by as much as 30%. These are more usable for viscous service.

 

  • Features
  • Datasheet
  • Informations

Spécifications

Design
Conforms to ISA RP 3.2 , DIN 1952 , BS 1042, ISO-5167

Types
Square edge concentric, Quadrant edged, Conical entrance, Eccentric, Segmental

Plate material
SS304 , SS316 , SS316L as standard. Hastelloy-C , Monel , PP , PVC , PTFE coated , etc. can be given on request.

Orifice Bore
In accordance with ISO-5167, BS-1042, ASME MFC 3M, R.W.Miller, L.K.Spink, AGA-3

Tab Plate
In the same material as plate & is welded to orifice plate. Tab plate integral to the Orifice plate (i.e. without welding) can also be offered as a special case.

Vent / Drain
Vent or Drain holes are provided as per customer's requirement. The diameter of the vent or drain holes are as per ISA RP 3.2

Flange Union Weld neck, Slip on, Threaded, Socket welded with RF or RTJ facing Orifice flanges are in accordance with ANSI B16.36 with minimum flange rating of 300# for sizes up to 8" or male - female flanges in accordance with ANSI B16.5

Pressure Tappings
Corner tappings are recommended for sizes upto 1 ½"; Flange taps from 2" to 16" ; D - D/2 taps for higher sizes

Gasket

CAF as per IS: 2712 Gr 0/1 , SS spiral wound + CAF , SS spiral wound + Grafoil, SS spiral wound + PTFE are normally supplied as per process requirement. Other materials available on request. For RTJ flanges , the plate is fixed on the plate holder. The plate holder is in Soft Iron material & acts as a gasket.

 

Studs / Nuts ASTM A193 Gr.B7/A-194 Gr.2H as standard, Other material on request.

Jack Screw ASTM A193 Gr.B7/A-194 Gr.2H as standard, Other material on request.

Download the datasheet répéteur RS422/485 (PDF Orifice Plates)

You want to get a quote, please click on the link and fill in the form. Note that our prices are digressive according to quantities.

 

For more information or any specific request, please contact our services. We shall get back to you as soon as possible.